SUCLAB

20%OFF
  • Laboratory Fume Hood Cfm Requirements,Lab Fume Hood Cfm Requirements,Laboratory Fume Hood Cfm Requirement

Factory Strict Checked Good Quality Steel Anti-corrosion Laboratory Fume Hood Cfm Requirements

stars, based on 0reviews
$1500.00now$1200.00 set
Quantity Price
10+ $1176.00
50+ $1140.00
10000items available
Contact Us

Factory Strict Checked Good Quality Steel Anti-corrosion Laboratory Fume Hood Cfm Requirements



Laboratory Fume Hood Cfm Requirements Product Introduction:


The purpose of using a fume hood is to discharge the harmful gases generated in the experiment

and protect the health of the experimenters, that is to say, to have a high degree of safety and

superior operability, which requires the fume hood to have the following functions:


(1) Release function

There should be a mechanism to absorb the harmful gas generated inside the fume hood by absorbing

the gas outside the hood, so that it is diluted and discharged to the outside.


(2) No backflow function

It should have the function that the airflow generated by the exhaust fan inside the fume hood will not reverse

the flow of harmful gases into the room from the inside of the fume hood. In order to ensure the realization of

this function, a fume hood and a ventilator should be connected with a single pipe. It cannot be connected with

a single pipe, and it is limited to the parallel connection of the same room on the same floor. The ventilator

should be installed as far as possible. The end of the pipe (or at the top of the layer).


(3) Isolation function

Use a non-slip glass window in front of the fume hood to separate the inside and outside of the fume hood.


(4) Supplementary functions

There should be a channel or alternative device for inhaling air from outside the fume hood when the harmful gas is discharged.


Laboratory Fume Hood Cfm Requirements Environmentally-Conscious Model:


High performance fume hoods has a series of design features to provide unsurpassed containment and operator protection:

1:Engineered baffle system provides proper air distribution

2:Constant air velocity (variable air volume) reduces energy use relative to sash position

3:Rounded corners at hood entrance reduce turbulence, improving efficiency

4:Aerodynamic sash pull

5:Containment trough with directional vanes and white Plascote finish adds durability and chemical resistance

6:Cord pass-through lets sash fully close without appliance cords getting in the way

7:Lower entrance safety bar provides a personal safety barrier 880mm high viewing area

8:White ResChem interior with vapor-proof fluorescent light.

9:458mm vertical opening with keyed sash stop to access 685mm set-up position

10:Double-wall construction for installation of plumbing and electrical service fixtures.



Laboratory Fume Hood Cfm Requirements Feature


(1) Fire protection: never use any flammable materials.


(2) Explosion-proof: The front end of the cabinet is made of 5mm explosion-proof glass, the two sides

of the cabinet are double-layer structure, and the inner lining is 6mm anti-fold special board. The double

-layer structure has the effect of releasing pressure for possible explosions in the cabinet.


(3) Corrosion resistance: External: The steel cabinet is pickled and phosphated and then sprayed with plastic,

which has excellent corrosion resistance. Internal: Acid and alkali resistant lining board with superior acid resistance.


(4) High efficiency: the deflector is a three-section detachable structure, and the position of the second deflector can

be adjusted according to the experimental requirements.


  Laboratory Fume Hood Cfm Requirements Advantage of Fume Hood:


1.It is safer to use anti-corrosive water tap.

2.Microprocessor control system, LED display.

3.With memory function in case of power-failure.

4.Made of porcelain white PP, resistant to acid, alkali and anti-corrosion.

5.Front window which is made of thick transparent toughened glass maximize

light and visibility inside the fume hood, providing a bright and open working environment.




Laboratory Fume Hood Cfm Requirements Picture drawing:

Factory Strict Checked Good Quality Steel Anti-corrosion Laboratory Fume Hood Cfm Requirements Factory Strict Checked Good Quality Steel Anti-corrosion Laboratory Fume Hood Cfm Requirements


Factory Strict Checked Good Quality Steel Anti-corrosion Laboratory Fume Hood Cfm Requirements Factory Strict Checked Good Quality Steel Anti-corrosion Laboratory Fume Hood Cfm Requirements


Factory Strict Checked Good Quality Steel Anti-corrosion Laboratory Fume Hood Cfm Requirements Factory Strict Checked Good Quality Steel Anti-corrosion Laboratory Fume Hood Cfm Requirements





COMPANY PROFILE


Factory Strict Checked Good Quality Steel Anti-corrosion Laboratory Fume Hood Cfm Requirements Factory Strict Checked Good Quality Steel Anti-corrosion Laboratory Fume Hood Cfm Requirements

Factory Strict Checked Good Quality Steel Anti-corrosion Laboratory Fume Hood Cfm Requirements Factory Strict Checked Good Quality Steel Anti-corrosion Laboratory Fume Hood Cfm Requirements

lab table:
Laboratory Fume Hood Cfm Requirements size: 1500*850*2350mm,Laboratory Fume Hood Cfm Requirements materials: full steel ,Laboratory Fume Hood Cfm Requirements deliver date:15days,Laboratory Fume Hood Cfm Requirements color:Blue, White or Optional(can customized),Laboratory Fume Hood Cfm Requirements using:chemical laboratory or school or hospital laboratory using,Laboratory Fume Hood Cfm Requirements shipping:by sea with wood box,Laboratory Fume Hood Cfm Requirements moq:5pcs,Laboratory Fume Hood Cfm Requirements Window:Anti-Explosive Glass,Laboratory Fume Hood Cfm Requirements specification:anti-corrosion,explosion proof ,energy efficient,Laboratory Fume Hood Cfm Requirements top: phenolic ,epoxy resin ,ceramics ,pp worktop
Recent Reviews
+